U-Boot 2008.10-mpcore-svn (May 20 2011 - 13:36:16)
Cavium Networks CNS3XXX SDK v0.7-1202
CPU: Cavium Networks CNS3000
ID Code: 410fb024 (Part number: 0xB02, Revision number: 4)
CPU ID: 900
Chip Version: c
DRAM: 128 MB
Flash: 32 MB
In: serial
Out: serial
Err: serial
CPU works at 300 MHz (600/1/2)
DDR2 Speed is 266 MHz
switch/phy reset
## Starting application at 0x03000000 ...
Hello ,This is SC world!
BootVersion SC V105,Build Time:May 20 2011 - 13:36:09
## Application terminated, rc = 0x0
checking the integrality of linux ... ...
flen is :19f9f00
fcrc is :8ae7488a
vmoffset is :100
vmsize is :812b09
vmcrc is :72cc8794
crc caled is :72cc8794
kernel length is :8465161(0x812b09)
fw version is :4.3.1-22+fk1
checking pass..
Hit any key to stop autoboot: 2 0
CNS3000 # help
? - alias for 'help'
base- print or set address offset
bdinfo - print Board Info structure
bootelf - Boot from an ELF image in memory
bootm - boot application image from memory
bootp- boot image via network using BOOTP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
cmp- memory compare
cp- memory copy
crc32- checksum calculation
date - get/set/reset date & time
dcache - enable or disable data cache
dhcp- boot image via network using DHCP/TFTP protocol
erase - erase FLASH memory
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
flashappimage- TFTP the firmware image to RAM,and copy the firmware image to the flash partition for firmware image
flashbootloader- TFTP load a bootloader image file to RAM, and copy the image to the bootloader partition in flash.
flinfo - print FLASH memory information
frtest- polling the status of factory reset button. It will return success if the user push factory reset button.
getmd - getmd basmac/serno/productID
go - start application at address 'addr'
help - print online help
icache - enable or disable instruction cache
iminfo - print header information for application image
loadb - load binary file over serial line (kermit mode)
loady - load binary file over serial line (ymodem mode)
loop- infinite loop on address range
md- memory display
mm- memory modify (auto-incrementing)
mmcinit - init mmc card
mtest- simple RAM test
mw- memory write (fill)
nm- memory modify (constant address)
pci - list PCI Configuration Space
phyop- operate standard phy register through mdio
ping- send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
return2Factory- Revert the bootloader configuration to factory settings.
rgpio- read gpio value for given GPIO pin
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
savemd - save the manuinfo to flash
sc_go - start sc standalone app at address 'addr'
setenv - set environment variables
setmd - setmd basmac/serno/productID value
switch_reg_read- Read a register value through mdio
switch_reg_write- write a register value through mdio
tftpboot- boot image via network using TFTP protocol
version - print monitor version
wgpio- set gpio value to 0/1 for given GPIO pin
CNS3000 # printenv
bootargs=root=/dev/mtdblock0 mem=128M console=ttyS0
bootcmd=cp.b 0x10080100 0x2000000 0x900000;go 0x2000000
bootdelay=2
baudrate=9600
ethaddr=00:53:43:xx:xx:xx
netmask=255.255.0.0
bootfile="/tftpboot/uImage"
tftp_bsize=512
udp_frag_size=512
ipaddr=192.168.2.1
serverip=192.168.2.100
stdin=serial
stdout=serial
stderr=serial
Environment size: 324/131068 bytes
CNS3000 # bdinfo
arch_number = 0x00000BB8
env_t = 0x00000000
boot_params = 0x00000100
DRAM bank = 0x00000000
-> start = 0x00000000
-> size = 0x08000000
ethaddr = 00:53:43:xx:xx:xx
ip_addr = 192.168.2.1
baudrate = 9600 bps
CNS3000 # bootp
BOOTP broadcast 1
*** Unhandled DHCP Option in OFFER/ACK: 44
*** Unhandled DHCP Option in OFFER/ACK: 44
DHCP client bound to address 192.168.2.99
TFTP from server 192.168.2.100; our IP address is 192.168.2.99
Filename 'openwrt-cns3xxx-uImage-mod'.
Load address: 0x800000
Loading: *#################################################################
#################################################################
#################################################################
###########################################
done
Bytes transferred = 1215144 (128aa8 hex)
-- VERSUCH 1 (bootm, 02008000) -------------------------------------------------
CNS3000 # bootm
## Booting kernel from Legacy Image at 00800000 ...
Image Name: OpenWrt Linux-3.3.8
Created: 2013-03-23 23:28:23 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1215080 Bytes = 1.2 MB
Load Address: 02008000
Entry Point: 02008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
(hängt fest)
-- VERSUCH 2 (bootm, 02000000) -------------------------------------------------
...
CNS3000 # bootm
## Booting kernel from Legacy Image at 00800000 ...
Image Name: OpenWrt Linux-3.3.8
Created: 2013-03-23 23:28:23 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1215080 Bytes = 1.2 MB
Load Address: 02000000
Entry Point: 02000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
(hängt fest)
-- VERSUCH 3 (go) --------------------------------------------------------------
...
CNS3000 # go 0x800040
enter do_eth_down!!!
## Starting application at 0x00800040 ...
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP Sat Mar 23 23:28:16 UTC 2013
[ 0.000000] CPU: ARMv6-compatible processor [410fb024] revision 4 (ARMv7), cr=00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Gateworks Corporation Laguna Platform
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c0398000 s4704 r8192 d15776 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
[ 0.000000] Kernel command line:
[ 0.000000] PID hash table entries: 64 (order: -4, 256 bytes)
[ 0.000000] Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Memory: 16MB = 16MB total
[ 0.000000] Memory: 12656k/12656k available, 3728k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc1800000 - 0xff000000 ( 984 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc1000000 ( 16 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0305000 (3060 kB)
[ 0.000000] .init : 0xc0305000 - 0xc032c260 ( 157 kB)
[ 0.000000] .data : 0xc032e000 - 0xc0348800 ( 106 kB)
[ 0.000000] .bss : 0xc0348824 - 0xc037407c ( 175 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] console [ttyS0] enabled
[ 0.020000] Calibrating delay loop... 119.70 BogoMIPS (lpj=598528)
[ 0.120000] pid_max: default: 32768 minimum: 301
[ 0.130000] Mount-cache hash table entries: 512
[ 0.140000] CPU: Testing write buffer coherency: ok
[ 0.160000] Setting up static identity map for 0x2a37c0 - 0x2a37f8
[ 0.170000] Brought up 1 CPUs
[ 0.180000] SMP: Total of 1 processors activated (119.70 BogoMIPS).
[ 0.200000] NET: Registered protocol family 16
[ 0.220000] L310 cache controller enabled
[ 0.230000] l2x0: 8 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x02540000, Cache size: 262144 B
[ 0.310000] bio: create slab <bio-0> at 0
[ 0.320000] SCSI subsystem initialized
[ 0.340000] usbcore: registered new interface driver usbfs
[ 0.350000] usbcore: registered new interface driver hub
[ 0.360000] usbcore: registered new device driver usb
[ 0.370000] Switching to clocksource freerun
[ 0.390000] NET: Registered protocol family 2
[ 0.430000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.510000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.600000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
[ 0.670000] TCP: Hash tables configured (established 512 bind 512)
[ 0.750000] TCP reno registered
[ 0.780000] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.850000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.930000] NET: Registered protocol family 1
[ 0.990000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.060000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 1.170000] msgmni has been set to 24
[ 1.220000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.300000] io scheduler noop registered
[ 1.350000] io scheduler deadline registered (default)
[ 1.410000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.490000] serial8250: ttyS0 at MMIO 0x78000000 (irq = 45) is a 16550A
[ 1.590000] CNS3xxx MII Bus: probed
[ 1.640000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.720000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.790000] i2c /dev entries driver
[ 1.830000] pca953x 0-0023: failed reading register
[ 1.900000] pca953x: probe of 0-0023 failed with error -11
[ 1.960000] pca953x 0-0027: failed reading register
[ 2.020000] pca953x: probe of 0-0027 failed with error -11
[ 2.090000] at24 0-0050: 1024 byte 24c08 EEPROM, read-only, 0 bytes/write
[ 2.710000] rtc-ds1672 0-0068: chip found, driver version 0.4
[ 2.780000] rtc-ds1672 0-0068: ds1672_get_datetime: read error
[ 2.850000] rtc-ds1672 0-0068: rtc core: registered rtc-ds1672 as rtc0
[ 2.930000] rtc-ds1672 0-0068: ds1672_get_control: read error
[ 3.000000] rtc-ds1672: probe of 0-0068 failed with error -5
[ 3.070000] gsp 0-0029: gsp chip found
[ 3.110000] MPcore Watchdog Timer: 0.1. mpcore_noboot=0 mpcore_margin=60 sec (nowayout= 1)
[ 3.210000] ------------[ cut here ]------------
[ 3.270000] WARNING: at kernel/irq/manage.c:1354 0xc0059544()
[ 3.340000] Modules linked in:
[ 3.370000] Backtrace:
[ 3.400000] Function entered at [<c001105c>] from [<c029ecc0>]
[ 3.470000] r6:0000054a r5:c02bf980 r4:00000000 r3:c033a9c8
[ 3.540000] Function entered at [<c029eca8>] from [<c001b93c>]
[ 3.610000] Function entered at [<c001b8e8>] from [<c001b978>]
[ 3.680000] r8:00000000 r7:c01df420 r6:00000000 r5:c0331000 r4:c0339498
[ 3.760000] r3:00000009
[ 3.790000] Function entered at [<c001b954>] from [<c0059544>]
[ 3.860000] Function entered at [<c00594d8>] from [<c029e4a0>]
[ 3.930000] Function entered at [<c029e3c0>] from [<c015c83c>]
[ 4.000000] r8:c0928cc0 r7:00000013 r6:c0343a5c r5:c036ff18 r4:c03394a0
[ 4.080000] Function entered at [<c015c81c>] from [<c015b718>]
[ 4.150000] Function entered at [<c015b654>] from [<c015b830>]
[ 4.220000] r7:00000013 r6:c0343a5c r5:c03394a0 r4:c03394d4
[ 4.280000] Function entered at [<c015b7c8>] from [<c015a140>]
[ 4.360000] r6:c015b7c8 r5:c0343a5c r4:00000000 r3:c015b7c8
[ 4.420000] Function entered at [<c015a0f0>] from [<c015b3d8>]
[ 4.490000] r6:c033fb80 r5:c0343a5c r4:c0343a40
[ 4.550000] Function entered at [<c015b3b8>] from [<c015b004>]
[ 4.620000] Function entered at [<c015af60>] from [<c015bb5c>]
[ 4.690000] Function entered at [<c015bab0>] from [<c015ca6c>]
[ 4.760000] Function entered at [<c015ca20>] from [<c03196bc>]
[ 4.830000] Function entered at [<c0319660>] from [<c0008618>]
[ 4.900000] r4:c081a000 r3:00000000
[ 4.940000] Function entered at [<c0008564>] from [<c03058d8>]
[ 5.010000] Function entered at [<c0305834>] from [<c001ed28>]
[ 5.080000] r5:c0305834 r4:00000000
[ 5.120000] ---[ end trace af06ac44d78af6c7 ]---
[ 5.180000] mpcore_wdt mpcore_wdt: cannot register IRQ30 for watchdog
[ 5.250000] mpcore_wdt: probe of mpcore_wdt failed with error -22
[ 5.330000] sdhci: Secure Digital Host Controller Interface driver
[ 5.400000] sdhci: Copyright(c) Pierre Ossman
[ 5.450000] sdhci-pltfm: SDHCI platform and OF driver helper
[ 5.520000] TCP cubic registered
[ 5.560000] NET: Registered protocol family 17
[ 5.620000] Bridge firewalling registered
[ 5.660000] 8021q: 802.1Q VLAN Support v1.8
[ 5.710000] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 4
[ 5.810000] Running on Gateworks Laguna
[ 5.850000] gpiochip_add: registered GPIOs 0 to 31 on device: cns3xxx_gpio0
[ 5.940000] gpiochip_add: registered GPIOs 32 to 63 on device: cns3xxx_gpio1
[ 6.020000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 6.100000] VFS: Cannot open root device "(null)" or unknown-block(0,255)
[ 6.180000] Please append a correct "root=" boot option; here are the available partitions:
[ 6.280000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,255)
[ 6.380000] Backtrace:
[ 6.410000] Function entered at [<c001105c>] from [<c029ecc0>]
[ 6.480000] r6:c0873009 r5:c0348d50 r4:c0873000 r3:00000001
[ 6.550000] Function entered at [<c029eca8>] from [<c029ee48>]
[ 6.620000] Function entered at [<c029edb8>] from [<c0305cb4>]
[ 6.690000] r3:c033e5cc r2:00000000 r1:c081bf58 r0:c02b9e24
[ 6.750000] r7:c0873000
[ 6.780000] Function entered at [<c0305adc>] from [<c0305dcc>]
[ 6.850000] Function entered at [<c0305d74>] from [<c0305f10>]
[ 6.920000] r5:c03258d8 r4:c03488a4
[ 6.970000] Function entered at [<c0305de0>] from [<c030594c>]
[ 7.040000] r5:c032a98c r4:c032a98c
[ 7.080000] Function entered at [<c0305834>] from [<c001ed28>]
[ 7.150000] r5:c0305834 r4:00000000